Split nylon flange bushings fit over clutch pedal cross shaft and inside cross shaft sleeve for clutch and brake pedals with 5/8" diameter cross shaft. These OER® reproduction bushings will help eliminate excessive side to side…
The bellhousing to clutch fork rubber boot seals out water and dust by sealing around the clutch fork and the rectangular fork hole in the clutch bellhousing. Every time you push the clutch pedal in your manual transmission Chevelle, the…
Set of four reproduction pedal shaft bushings. Used with all automatic and manual pedals. Group 0.831 and 4.626 GM Part #: 3798256, 3965692, 1247439, 140048221…
The clutch cross shaft is a piece of steel that slides into the transmission case, and it is the pivot point for the fork that pushes onto you clutch diaphragm. Basically, if it were to fall out you wouldn't be able to operate the clutch…
Stock Replacement Original GM Seals Z-Bar At Frame Side Ball Stud Keeps Debris From Entering Z-Bar Causing Pre Mature Ware This stock replacement ball stud dust seal is manufactured by GM or by one of its authorized suppliers for use as a…
Stock Replacement Original GM Retains Swivel To Z-Bar And Clutch Pedal To Upper Rod This stock replacement clutch linkage retainer clip is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part. You…
Best Quality Reproduction Bellcrank Seals Heavy, Die Cut Felt Fiber As Original Keeps Grease In The Clutch Bellcrank Where It Belongs 9/16 ID & 1? OD This little Camaro part does a big job and will wear out easily from years of use and…
Reproduction Of Original Correct Spun Molded Unit With Integrated Metal Retaining Plate Featured In 1978-87 Clutch Linkage Diagram As Number 22 This clutch boot assembly is 100% correct. This is the boot that installs on the firewall in…
Superior Reproduction of Original Black Molded Rubber One Required per Car Fits Big Block or Small Block Cars The El Camino Store brings you this reproduction clutch fork boot to replace a commonly worn part. The bellhousing to clutch fork…
Reproduction Of Original Attaches Clutch Pedal To Z-Bar Through The Firewall This Chevelle reproduction upper clutch rod has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find…
Reproduction Of Original This Chevelle reproduction z bar has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and function will work superbly for your…
Stock Replacement Original GM Correct Spring For Ball Stud On Frame Side This stock replacement ball stud spring is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part. You will find the fit and…
Stock Replacement Original GM 4 Needed Per Brake And Clutch Pedal Support Bolt Featured In 1978-87 Clutch Linkage Diagram As Number 13 Featured In 1959-77 Clutch Linkage Diagram As Number 2 Will Not Replace Large White Bushing On 1959-1960…
Stock Replacement 2nd Design Ball, Is A 1/4 Inch Shorter Then 1st Design Will Replace 1st Design Ball Studs This stock replacement ball stud is manufactured by GM or by one of its authorized suppliers for use as a factory replacement part…
Authentic hardware you need to correctly reassemble the transmission components. Most fasteners have correct markings for the time period. This kit includes one retaining clip.
…
Reproduction Of Original Includes Integral Rubber Seal This Chevelle reproduction clutch bellcrank pivot stud has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit and…
Accurately machined Frame pivot ball stud fits all original and reproduction big and small block clutch bellcranks. Unlike cheap knock-offs offered elsewhere, ours are heat treated for hardness as original. Black oil finish. Overall length…
Reproduction Of Original Correct 6-1/4 Length Includes Swivel Set Nuts P/N 11-2250 Sold Separately (2 Needed) Retainer Clip P/N 11-2010 Sold Separately This El Camino reproduction bell crank lower push rod has been manufactured to original…
Reproduction Of Original Correct 6-1/4 Length Includes Swivel Set Nuts P/N 11-2250 Sold Separately (2 Needed) Retainer Clip P/N 11-2010 Sold Separately This El Camino reproduction bell crank lower push rod has been manufactured to original…
Stock Replacement Original GM Correct Foam Rubber Seal Pre Attached Featured In 1978-87 Clutch Linkage Diagram As Number 35 This stock replacement clutch fork ball stud is manufactured by GM or by one of its authorized suppliers for use as…
Good Quality Reproduction From Clutch Pedal To Z-Bar Nice reproduction of your Chevelle's clutch upper pushrod. Original clutch components can become stressed and fail after years of use. Why take the chance? Replace your original upper…
Reproduction Of Original Welds To Lower Firewall Used To Anchor Bellcrank Spring To Firewall This Chevelle reproduction clutch bellcrank firewall return spring bracket on firewall has been manufactured to original factory specifications…
Reproduction Of Original Correct Short Bracket Weld To Frame This Chevelle reproduction pivot bracket has been manufactured to original factory specifications using today's modern manufacturing techniques. You will find the fit, finish and…